J&S Tool F-Series Wheel Dressers
Fluidmotion Wheel Dressers
Dressing complex forms on cylindrical, surface, tool and cutter grinder wheels with guaranteed .0001 accuracy is easy with a micrometer fed J&S Fluidmotion Wheel Dresser. You won’t believe how simple it is, even for a beginner, to dress two angles tangent to a radius in one continuous motion – with only one setting. Better still, the diamond will automatically return to the center position after dressing the angles.
This is not new, Fluidmotion dressers have been consistently performing in this manner since J&S introduced the first model over 60 years ago. Quality proven and tested, many of these original, American made units are still performing with outstanding accuracy after being rebuilt at our facility.
| ELIMINATE ELABORATE SETUPS | No need to pre-set diamond or use any other tool except a micrometer and a simple hex wrench. No Gage Block–Master Gage setting–Jo Block–Parallel Bar–Surface Plate–Height Gage– Dial indicator. No movement of dovetails necessary to form angles. The angle is dressed by continuing to push handle in both directions after radius is formed. No need to use Gibs & V-Ways other than positioning surfaces. |
| ACCURATE–RAPID, REPEAT FORM- DRESSING | Fluidmotion generates clean, precise wheel profiles entirely free of chatter marks. Without FLUIDMOTION a perfect blend of angles and radius is improbable. |
| PRECISE SHARP CONTOURS | Concave or convex, at a full 180 degrees, are obtained consistently with 0.0001” accuracy guaranteed. |
| CONVEX RANGE | Zero to 3 inches. If the models desired in this catalog do not answer your particular grinding requirements, special dressing equipment can be furnished to your specifications to dress wheels up to 42” in diameter. |
| CONCAVE RANGE | 1/32” to 3 1/2 inches. |
| PRECISION | Hold Intersecting angles –12 to 15 seconds. This is accomplished by operating upright and handle. |
| SET UP TIME | Setting up two angles requires 10 seconds. Setting two angles and radius requires less than 3 minutes. |
| MOST DURABLE DRESSER AVAILABLE | Manufactured in the U.S.A. from hardened, ground and lapped alloy steels. No wear surfaces. Swivels on sealed bearings. |
Micrometer Base
- Hardened and ground base with controlled fine diamond infeed. Feed is independent of table movement having 1-3/16" travel. Especially recommended for dressing small radii.
# F-50 - for up to 7" diameter wheel
J&S Part No. 10000
- Easily coupled with our Wheel Guard Mounting, G Micrometer Base and fixture for Under The Wheel Dressing. Adaptable to tool and cutter grinders.
# RFG-50
J&S Part No. 10100
- Model F-50 (above) mounted on our G Micrometer base.
# F-55 - for up to 8" diameter wheel
J&S Part No. 10001
- Easily coupled with our Wheel Guard Mounting, G Micrometer Base and fixture for Under The Wheel Dressing. Adaptable to tool and cutter grinders.
# RFG-55
J&S Part No. 10101
- Model F-55 (above) mounted on our G Micrometer base.
# F-618 - for up to 12" diameter wheel
J&S Part No. 10002
- Easily coupled with our G Micrometer Base and fixture for Under The Wheel Dressing.
# RFG-618
J&S Part No. 10102
- Model F-618 (above) mounted on our G Micrometer base.
Wheel Dresser for: Cylindrical, Universal and Surface Grinders
# F-750A - for up to 14" diameter wheel
J&S Part No. 10004
- This model has an adjustable height of 4" to 7 1/2" above the table with (2) holder for diamonds. Dresser has been designed primarily for use on cylindrical and universal grinders. Units are adapted with a Solid Angle Ramp. Will dress both external and internal wheels. Units are provided with a shock arrester which eliminates vibration when the diamond is extended to maximum position on 14" diameter wheel. Also used on surface, tool and cutter grinders. Easily coupled with our G Micrometer Base and fixture for Under The Wheel Dressing. For radius and angle capacities, refer to Fluidmotion Wheel Dresser Specifications Chart.
# RFG-750A
J&S Part No. 10104
- Model F-750A (above) mounted on our G Micrometer base.
Note: Modified base may be required to adapt wheel dressers to grinders. Consult factory for recommendations or see Adapters and Attachments.
Click to see the Dresser Chart
Click to see Wheel Dresser Attachments
