J&S Tool E-Series Wheel Dressers

Brand:

Call for Pricing

(No reviews yet) Write a Review

J&S Tool

J&S Tool E-Series Wheel Dressers

Fluidmotion Wheel Dressers


Dressing complex forms on cylindrical, surface, tool and cutter grinder wheels with guaranteed .0001 accuracy is easy with a micrometer fed J&S Fluidmotion Wheel Dresser. You won’t believe how simple it is, even for a beginner, to dress two angles tangent to a radius in one continuous motion – with only one setting. Better still, the diamond will automatically return to the center position after dressing the angles.


This is not new, Fluidmotion dressers have been consistently performing in this manner since J&S introduced the first model over 60 years ago. Quality proven and tested, many of these original, American made units are still performing with outstanding accuracy after being rebuilt at our facility.

ELIMINATE
ELABORATE SETUPS
No need to pre-set diamond or use any other tool except a
micrometer and a simple hex wrench. No Gage Block–Master
Gage setting–Jo Block–Parallel Bar–Surface Plate–Height Gage–
Dial indicator. No movement of dovetails necessary to form angles.
The angle is dressed by continuing to push handle in both
directions after radius is formed. No need to use Gibs & V-Ways
other than positioning surfaces.
ACCURATE–RAPID,
REPEAT FORM-
DRESSING
Fluidmotion generates clean, precise wheel profiles entirely free of
chatter marks. Without FLUIDMOTION a perfect blend of angles and
radius is improbable.
PRECISE SHARP
CONTOURS
Concave or convex, at a full 180 degrees, are obtained consistently
with 0.0001” accuracy guaranteed.
CONVEX RANGE Zero to 3 inches. If the models desired in this catalog do not answer
your particular grinding requirements, special dressing equipment
can be furnished to your specifications to dress wheels up to 42” in diameter.
CONCAVE RANGE 1/32” to 3 1/2 inches.
PRECISION Hold Intersecting angles –12 to 15 seconds. This is accomplished by
operating upright and handle.
SET UP TIME Setting up two angles requires 10 seconds. Setting two angles and radius
requires less than 3 minutes.
MOST DURABLE
DRESSER
AVAILABLE
Manufactured in the U.S.A. from hardened, ground and lapped alloy steels.
No wear surfaces. Swivels on sealed bearings.


Micrometer Base

  • Hardened and ground base with controlled fine diamond infeed. Feed is independent of table movement having 1-3/16" travel. Especially recommended for dressing small radii.


# E-75 - for up to 12" diameter wheel
J&S Part No. 10200

  • Easily coupled with our fixture for Under The Wheel Dressing and our C Micrometer base. Adaptable to tool and cutter grinders.

# REC-75
J&S Part No. 10300

  • Model E-75 (above) mounted on our C Micrometer base.


# E-85 - for up to 14" diameter wheel
J&S Part No. 10201

  • Easily coupled with our fixture for Under The Wheel Dressing and our C Micrometer base.

# REC-85
J&S Part No. 10301

  • Model E-85 (above) mounted on our C Micrometer base.


# E-95 - for up to 20" diameter wheel
J&S Part No. 10202

  • Easily coupled with our fixture for Under The Wheel Dressing and our C Micrometer base.

# REC-95
J&S Part No. 10302

  • Model E-95 (above) mounted on our C Micrometer base.


Wheel Dressers for: Cylindrical, Universal and Surface Grinders

# H-24A - for up to 24" diameter wheel
J&S Part No. 10203

  • This model has an adjustable height of 6” to 10” above the table with two (2) holders for diamonds. Dresser has been designed primarily for use on cylindrical and universal grinders. Units are adapted with a Solid Angle Ramp. Will dress both external and internal wheels. Unit is provided with a shock arrester which eliminates vibration when diamond is extended at maximum position on 24” diameter wheels. Easily inserted on a C Micrometer Base and fixture for Under The Wheel Dressing.

# RHC-24A
J&S Part No. 10303

  • Model H-24A (above) mounted on our C Micrometer base.


# H-30A - for up to 30" diameter wheel
J&S Part No. 10204

  • Has an adjustable height of 6” to 11 3/8” above the table with two (2) holders for diamonds. Dresser has been designed primarily for use on cylindrical grinders. Units are adapted with a Solid Angle Ramp. Will dress both external and internal wheels. Unit is provided with a shock arrester which eliminates vibration when diamond is extend at maximum position on 30” diameters wheels.

# RHC-30A
J&S Part No. 10304

  • Model H-30A (above) mounted on our C Micrometer base.

Note: For wheel diameters from above 30” up to 36” consult factory for recommendations.



# RHS-36 - for up to 42" diameter wheel
J&S Part No. 10305

  • This unit has an adjustable height of 15” to 20” above the table with two (2) holders for diamonds. Dresser has been designed primarily for use on roll grinders. For Radius and angle capacities, refer to page 19 Fluidmotion Wheel Dresser Specifications Chart.

Note: Modified base required to adapt wheel dressers to grinding machines. Consult factory for recommendations or see Adapters and Attachments.



Click to see the Dresser Chart


Click to see Wheel Dresser Attachments